Welcome to Accuscreen Supplies Inc. the innovative leader in the screen print industry. close

Cleaning Chemicals

109G INK DEGRADENT

APPLICATION
PROCHEM 109G is a water miscible ink degradent. It is highly effective on laquer stencil, plastisol, poster, multi-purpose (solvent based) and UV inks.

  1. When used for screen reclamation, begin by carding excess ink from screen.
  2. Spray PROCHEM 109G onto the mesh and then scrub both sides with a non-abrasive brush or pad until the ink is liquefied.
  3. High pressure water rinse all ink residue from the screen. By washing from the bottom to top, you will prevent the possibility of ink locking itself back onto the mesh when it comes in contact with the rinse water. *Check with your local sanitation district regarding limitations on inks that are to be rinsed into drain.

AVAILABLE SIZES:
1 GAL. CONT., 5 GAL. PAIL, 30 GAL. DRUM, 55 GAL. DRUM

ProChem 109G


top

GR-9 INK DEGRADENT

APPLICATION
GR-9 is a water soluble ink degradent. It is highly effective on laquer ink, laquer stencil, enamel, vinyl, mylar, poster, UV and epoxy ink.

  1. When used for screen reclamation, begin by carding excess ink from screen.
  2. Spray GR-9 onto the mesh and then scrub both sides with a non-abrasive pad or brush until the ink is liquefied.
  3. High pressure water rinse all ink residue from the screen. By washing from the bottom to top, you will prevent the possibility of any ink locking itself back onto the mesh when it comes in contact with the rinse water. *Check with your local sanitation district regarding limitations on inks that are to be rinsed into drain.

AVAILABLE SIZES:
1 GAL. CONT., 5 GAL. PAIL, 30 GAL. DRUM, 55 GAL. DRUM

GR-9


top

 GB-1000 HAZE REMOVER

APPLICATION
This product is a paste ghost / image stain remover. GB-1000 is designed for the removal of cured ink stains. *This product should be mixed thoroughly before using.

  1. Apply GB-1000 to the ink side of the screen. Allow the coating to penetrate up to 5 minutes. For tougher stains, brush product on both sides of the screen.
  2. Low pressure rinse (flood rinse with tap water pressure), removing all chemicals from the screen. This step protects the employees from caustic being splashed back during high pressure rinse.
  3. High pressure water rinse to remove any remaining residue.

AVAILABLE SIZES:
1 GAL. CONT., 5 GAL. PAIL


GB-1000


top

GB-2000 HAZE REMOVER

APPLICATION

  1. Apply GB-2000 to the ink side of the screen. Allow the coating to penetrate up to 5 minutes. For tougher stains, brush product on both sides of the screen.
  2. Low pressure rinse (flood rinse with tap water pressure), removing all chemicals from the screen. This step protects the employees from being splashed back during high pressure rinse.
  3. High pressure water rinse to remove any remaining residue.

AVAILABLE SIZES:
1 QT. CONT., 1 GAL. CONT., 5 GAL. PAIL


GB-2000


top

HC-100 HAZE AND IMAGE REMOVER 

APPLICATION

Mix this product thoroughly before using.

  1. Apply HC/100 to the ink side of the screen. Allow the coating to penetrate up to 5 minutes. For tougher stains, brush product on both sides of the screen.
  2. Low pressure rinse (flood rinse with tap water pressure), removing all chemicals from screen. This step protects the employees from caustic being splashed back during high pressure rinse.

AVAILABLE SIZES:
1 QT. CONT., 1 GAL. CONT., 5 GAL. PAIL

HC 100 Haze Remover


top

DEHAZER 150 LIQUID STAIN REMOVER

APPLICATION
ProChem DEHAZER 150 This product is a viscous dehazer and degreaser that is designed for a variety of inks. PROCHEM DEHAZER 150 cleans mesh of stains with less noticeable odor and works better than most paste stain removers.

  1. Before using PROCHEM DEHAZER 150, remove all ink and emulsion from the screen.
  2. Brush product on the ink side of a wet or dry screen. Agitate on both sides of the screen with a non-abrasive brush or pad and set aside for approximately 3 to 30 minutes.
  3. High pressure water rinse, spraying from the bottom to top, on the print side of the screen. Reverse screen and high pressure rinse. Allow screen to dry.

AVAILABLE SIZES:
1 GAL. CONT., 5 GAL. PAIL

Dehazer 150


top

LSR/10 LIQUID STAIN REMOVER

APPLICATION
This product is a liquid ghost/image remover that is designed for use with a variety of inks. LSR/10Æ cleans mesh of cured ink stains with less noticeable odor and works better than most liquid stain removers. LSR/10 contains a proprietary mesh protector. *Before using LSR/10Æ, remove all ink residue and emulsion from the screen.

WET APPLICATION:
Brush LSR/10 on both sides of screen, allow to dwell 1-3 minutes, then high pressure rinse starting from the bottom of the screen to the top on the print side of the screen. Repeat high pressure rinse on the reverse side. Apply a CCI degreaser and remove by a low pressure flood rinse to both sides of screen. If residue stain is present, use dry application method.

DRY APPLICATION:
Brush LSR/10 on completely dry screen and allow product to dry. Reactivate LSR/10 by applying a CCI screen wash. (Contact your CCI sales representative for proper product recommendation). Agitate by brushing in a screen wash on both sides of screen until product is dissolved. High pressure rinse both sides of screen, starting from the bottom to the top. Apply a CCI degreaser and remove by low pressure flood rinsing both sides of screen.

AVAILABLE SIZES:
4×1 QT. CASE, 1 GAL. CONT., 5 GAL. PAIL, 30 GAL. DRUM, 55 GAL. DRUM

LSR/10


top

THE PINK STUFF DEHAZER/ DEGREASER

APPLICATION
This product is a vicious dehazer and degreaser that is designed for a variety of inks. THE PINK STUFF cleans mesh of stains with less noticeable odor and works better than most hazardous stain removers. The Pink Stuff leaves your fabric free of all oils and contaminants, which will reduce the incidence of pinholes.

  1. Before using The Pink Stuff, remove all ink residue and emulsion from the screen.
  2. Brush product on the ink side of a WET screen. Agitate on both sides of the screen with a brush or pad and set aside for approximately 1 to 10 minutes.
  3. High pressure water rinse, spraying from the bottom to top, on the print side of the screen. Reverse screen and high pressure rinse, then use low pressure water and flood rinse the complete screen. Allow screen to dry before coating.

The Pink Stuff


top

ES-900 CONCENTRATED EMULSION REMOVER

APPLICATION
ProChem ES-900 in diluted form, will quickly and economically remove all types of photo-polymer, diazo or capillary film on all types of mesh. This product will not crystallize, coagulate or plug rinse jet nozzles on automatic screen reclaiming units.

  1. Remove any ink residue and flush the screen with water.
  2. Dilute 1 part of ProChem ES-900 with up to 30 parts of water. Spray product on print side of screen. Allow sufficient time to penetrate the coating, approximately 30 seconds.
  3. Rinse thoroughly with high pressure water.

AVAILABLE SIZES:
1 GAL. CONT., 5 GAL. PAIL

ES 900


top

MICROPACK SCREEN WASH / EMULSION REMOVER

APPLICATION:
MICROPACK is a one-step screen wash / emulsion remover which is formulated to work best on most inks, especially plastisol inks. MICROPACK will also remove all photo polymer, diazo and capillary film emulsions. It is safe on all types of mesh.

  1. Card excess ink from screen. Mix in additive II (separately packaged) to MICROPACK.
  2. Apply MICROPACK on both sides of the screen, then scrub with a non-abrasive pad or brush until ink is liquefied. Allow to dwell for 30 seconds. For best results, dip pad or brush in water prior to scrubbing the screen.
  3. High pressure water rinse. By washing from the bottom to the top, you will prevent the possibility of any ink or emulsion locking itself back onto the mesh when it comes in contact with the rinse water.

AVAILABLE SIZES:
1 GAL. CONT., 5 GAL. PAIL


Micropack


top

PERMX PERMANENT EMULSION HARDENER

APPLICATION
ProChem PermX is a one part permanent chemical hardener designed to increase the water resistance of photo-emulsions. ProChem PermX increases the print durability and reduces premature stencil breakdown. It is excellent for high humidity conditions. With some emulsions, ProChem PermX will produce an absolute waterproof stencil that is difficult to reclaim.

  1. Expose screen and thoroughly wash out image area.
  2. Apply ProChem PermX to both sides of a dry screen.
  3. For best results, allow ProChem PermX to dwell on the screen until it has completely dried.
  4. Rinse image area to prevent blockage.

AVAILABLE SIZES:
1 QT. CONT., 1 GAL. CONT., 5 GAL. PAIL, 55 GAL. DRUM


PermiX


top